42Q-MES0174-A OEE Workbench

42Q Home > Production > OEE Workbench
 

Production
OEE Workbench 
Version MES15.77
Revision E1

 

Introduction

Batch/Lot Process form is an interface that allows for basic data collection, including location selection, basic defect recording, attribute/assembly data if configured. TAKT time display and OEE basic data recording is available using asset integration through CMMS. All the activities are recorded in Unit History against the serial record.

 

Target Maintenance

To use the Batch/Lot Process Control function, the following items are required:

1. A serial (batch in this case)  in process status for the location to
2. Setup target maintenance with setup time and cycle time for the part number 

 

Go to Shop Floor Control> Configuration> Target maintenance> soms_target

 

Figure 1: Target Maintenance 

 

Note: Users have to set up the Target Cycle Time and Setup Time for the part number and process they will be working on using the Create button on the top right.

 

For more details on target maintenance please refer to Target Maintenance.

 

Machine Integration

To set up the machine in CMMS Asset go to Shop Floor Control> Configuration> CMMS Asset> Asset.

 

Figure 2: CMMS-Asset

Select the Add button to add a new machine (asset). The Add Asset Window will be displayed to enter the required information.

 

Figure 3: Scan / Add Asset

 

Figure 4: Add Asset Information

 

Note:  The following fields are mandatory: Asset Id, Asset Name, and Asset Type.

 

Users must map the CMMS Asset to the location operator who will perform the job.

To map the machine to the respective location, go to Shop Floor Control> Configuration> CMMS Asset> Asset Mapping.

 

Figure 5: Asset Mapping 

Select Add and fill the form with the Location Name and Machine for mapping as shown in the figure.

 

Figure 6: Add Asset Mapping

 

For more details on asset management refer to CMMS Asset.

Users have to set up Problems/ Reasons for the machine. To add the problems in CMMS under Problem, users must have the problem type and problem category created before the problem creation.

 

Assign the Problem to Asset Type for the assets.

 

Figure 7: Asset Type

 

Figure 8: Edit Asset Type

 

OEE Workbench

Without Asset Integration

Once all the prerequisites have been set up the users have to access the Batch/Lot Process control form; to do so navigate to Production> OEE Workbench

 

Figure 9: OEE Workbench

 

Users have to Scan the Location they want to work on to be able to see all the units that are available to that location. 

 

Figure 10: Select Device or Location

 

Note: Batch can also be scanned in the serial number text box. The P1, P2 are the priority based on the shop order sequencing.  If there is no sequencing/ priority defined the orders appear as the oldest order first.

 

Figure 11: OEE Workbench Location and Serial Numbers

 

Users have to select the unit to work on. It will give a summary of the unit, such as part number, unit quantity (can be updated by user), shop order quantity. As there is no machine integration the machine status is N/A.

 

Figure 12: Unit to Work On Screen

 

Note: There is a new rule that states that when a location name starts with ‘S’, the operation will not be considered as SETUP (it will not be hard-coded), instead, it will take as reference the setup done in the process_mapping to retrieve the operations. However, if the process_mapping does not contain the ‘S’, or is empty, ‘S’ will be set up by default.

 

Select START to begin the operation. If there are any prompts (attributes or assembly setups) they must be completed.

 

Figure 13: Attributes or Assembly Setups

1. The clock will start ticking and users will be able to see the time under which the operation starts. This is the Remaining Time (standard time*qty + setup time), Setup Time, and Standard Time based on the SOMS table set up in target maintenance.
2. Multiple operations are available for operators, such as Add Comment, Add Defect, and End of the process.
3. Once all the activities have been finished, users can select the END button to move the unit to the next step based on the route. All the activities will be recorded in Unit History.

Figure 14: MESWeb Unit history

 

 

 

With Asset Integration

Once all the prerequisites have been set up the users have to access the Batch/Lot Process control form; to do so navigate to Production> OEE Workbench (Figure 7). Users have to Scan the Location they want to work on to see all the units that are available at that location.

 

Note: Batch can also be scanned in the serial number text box.

 

Figure 15: Scanned Location

 

The next step is to select a unit and quantity on which the operator will work on. 

 

Figure 16: Selected Unit to Work On

 

To begin the operation, users must select START. Once done, the clock will start ticking and the user will be able to see the start time under the remaining time.

 

Figure 17: Running Machine Example

Note: The machine status comes from CMMS, if the machine is under maintenance in CMMS, the status of the machine will be down here.

 

To stop the machine, users must select the STOP button and then, specify a reason for stopping the machine. The reasons are the problems that have been created in CMMS Asset.

 

Figure 18: Stop Category

A confirmation message will be displayed asking to proceed or cancel the action. Once confirmed, the problem will be recorded on the machine and a success message will be displayed.

 

Figure 19: Information Update Message

The system will advise that the machine is “DOWN”. Once the problem has been fixed, the operator can select again the Start Machine button and the Machine Status will be changed to “RUNNING”.

 

Figure 20: Down Machine Example

 

See a complete Batch route list of a location’s process

 

OEE Workbench has the ability to display the information of scannable batches based on its location's process. This functionality allows users to:

• See the related locations to a device.
• See the complete route in a location.
• Identify which of the Shop Orders are active (they can be serialized or non-serialized batch).

To do so:

1. Select the Define Scan button. The system will display the Changing Scan Device window.
2. Select the Device option.
3. Enter a Station ID to select it from the drop-down list.
4. Select the Confirm button to proceed, or Cancel to quit.

Figure 21: Changing Scan Device

 

5. Then, input a Serial Number in the corresponding field to scan it.

 

Figure 22: Serial Number Field

 

6. Once done, the list of the shop orders in the route will be displayed on the left side of the panel. In this section, users can see which of the shop orders are active. 

Figure 23: List of Shop Orders in a Route

 

 

7. Select a shop order from the list.
8. To begin the process select the START button. The status of the shop order will be displayed as “RUNNING”.
9. To complete the process, select the END button. 
10. A confirmation message will appear asking “Do you want to complete the booking?”. Select Confirm to proceed or Cancel to quit.

 

Figure 24: Finishing Job

 

11. Once confirmed, a success message will appear at the right bottom of the panel, pointing out that the unit has passed from the current to the next unit location.

 

Figure 25: Success Message

---

Labor Tracking - OEE Workbench

The module of OEE Workbench has also a Labor Tracking widget where users are able to realize manually (default configuration) or automatically (sections 6.1 and 6.2) different actions for Direct or Indirect labors of a shop order, in a specific location:

• Clock-in
• Clock-out
• Pause
• Resume

 

To execute the Labor Tracking functionalities, just select the corresponding icon located at the left bar and then clock in a Shop Order or an Indirect Labor:

Figure 21: Labor Tracking Icon

Figure 22: Clock in a Shop Order

 

Users will find two tabs, one for Labor Tracking and the other for Crews. And two buttons for labor, one for Direct and the other for Indirect. 

 

Clock-in direct labor

1. To clock in time in a Shop Order, type the Shop Order in the corresponding field and then, select the Clock-In button below. (Figure 20)
2. A success message will appear at the right bottom of the page, indicating that direct-shop-order labor has been started and that a new card has been created and added to the Direct Labor/Shop Order list. This also confirms that the Direct Labor is being tracked.

 

Figure 23: Success Message ‘Started direct shop order labor’

 

Clock-out direct labor

1. To clock out one Shop Order, select the stop icon inside the corresponding shop order box. In case users want to stop more than one labor at a time, select the stop icon located at the top of the list.
2. A confirmation message will appear. To complete the action, select Confirm or Cancel to quit.

Figure 24: Clock-out Selected Labor

 

Figure 25: Multiple Selection

 

Pause direct labor

1. To pause labor, select the pause icon.
2. A confirmation message will be displayed. Select Confirm to complete the action, or Cancel to quit.
3. Once confirmed, a success message will appear at the right bottom of the page, indicating that direct-shop-order labor has been started.

 

Figure 26: Pause Labor

 

Figure 27: Success Message ‘Paused direct shop order labor’

Resume direct labor

1. To resume a paused labor, select the resume icon inside the shop order box or the one at the top of the list.
2. A confirmation message will appear. To complete the action, select Confirm or Cancel to quit.
3. Once confirmed, a successful confirmation will appear at the top right of the screen.

 

Figure 28: Resume Labor 1

 

Figure 29: Success Message “Direct Shop Order labor already started”

 

Figure 30: Resume Labor 2

 

Figure 31: Success Message ‘Started previously paused direct shop order labor’

 

Start indirect labor

As mentioned above, users are able to start indirect labors that will be recorded in the unit history. To do so:

1. Select the Indirect tab of the Labor Tracking widget.
2. Write down an indirect labor in the corresponding field or select one from the drop-down list. The selected indirect labor will be listed below.

 

Figure 32: Indirect Labor Selection

 

1. Click the start icon to continue.
2. A confirmation message will appear. Select Confirm to proceed or Cancel to quit.
3. Once confirmed, a success message will appear.

Figure 33: Start indirect labor

 

Figure 34: Started indirect labor message

 

 

Crews

The Labor Tracking widget, in OEE Workbench, allows users to join or leave a current active crew, as is explained below.

 

To join a crew as a regular user

1. Open the Crew tab of the Labor Tracking widget to see the current active crews.
2. Select the Join button of a desired crew. A confirmation message will be displayed asking to pause labors and join the selected crew.
3. Click Confirm to proceed, or Cancel to quit.
4. Two pop-up messages will appear: 
   • Message 1 confirming that crew changes were saved
   • Message 2 advising that the direct shop order labor was successfully paused

 

Figure 35: Join a crew

 

Figure 36: Saved crew changes pop-up messages

 

To leave a crew as a regular user

Users are also allowed to leave a crew by using this widget. To do so:

1. Open the Crew tab of the Labor Tracking widget.
2. Select the Leave button of a desired crew. A confirmation message will be displayed.
3. Click Confirm to proceed, or Cancel to quit.
4. A pop-up messages will appear confirming that the crew changes were saved.

Figure 37: Leave a crew

 

To add new members as a crew user

Users can log in to the portal as crew users. In this case, the addition of a new crew member requires users to log in with their personal credentials.

1. Log in the 42Q portal as a crew user and navigate to Production > OEE Workbench.
2. Select the Labor Tracking icon.
3. Open the Crew tab to see the current active members of that crew.
4. Select the + button located above the members’ list. A pop-up window will appear to log into the portal.

Figure 38: Add a Member as Crew User

 

Once logged, the system will announce that the change was done and the information of the new member will appear in the members’ list of the crew. 

 

Figure 39: Saved Crew Change(s) Message

 

To leave a crew as a crew user

Users are also able to leave a crew if they logged into the portal with a crew user. The system will ask for their personal credentials, as well. To do so:

1. Select the Leave button of the user that will leave. 
2. A new window will open asking for username and password. Write down the required information. 

Once logged, a pop-up message will be displayed informing the user that the crew change was saved (Figure 37). And the member that left the crew will not appear anymore in the members list.

Figure 41: Leave a Crew as Crew User

 

Smart insights

The Smart Insights functionality performs semi-automatically the start/resume labor records upon a serial number is scanned, helping users to save time and avoid manual and forgettable tasks. 

Once a serial number has been scanned, the system will prompt a confirmation message suggesting three options:

• Clock-in/Resume
• Dismiss
• Dismiss and don’t ask again

 

Figure 42: Smart insights alert message

 

Users must set up previously this feature that can be configured based on a generic attribute or based on a flex field for location or process.

 

To set values based on a generic attribute

1. Navigate to Administration > Generic Attribute Maintenance.
2. Search the “ps_insights_enabled” generic attribute.
3. Select the corresponding checkbox.
4. Click the Edit Generic Attribute button located at the top of the list. The Generic Attribute Form will be displayed. 
5. Input the desired value:
   • “True” value —> turn on the alert message
   • “False” value —> turn off the alert message
6. Select Save to proceed or Cancel to quit.

 

Figure 43: Generic attribute form

 

To set values based on a flex field

With a flex field configuration for process or location, using the ps_labor_tracking_option macro configuration.

 

Configuration by Location 

1. Navigate to Shop Floor Control > Configuration > Shop Floor Configuration > Location.
2. Select a location.
3. Click the Edit button to display the Location Form.
4. Open the Flex Field Form tab.
5. Search “ps_labor_tracking_option”.
6. Input the desired value:
   • “Insight” value to allow users clock-in/clock-out manually through an alert message (figure 28)
   • “Off” value to disable the alert message
   • “Auto” value to clock-out automatically
7. Save the action.

 

Figure 44: Location Form

 

Configuration by Process 

1. Navigate to Shop Floor Control > Configuration > Shop Floor Configuration > Location.
2. Select a location.
3. Click the Process Maintenance button to display the Process List.
4. Select a process.
5. Click the Edit button to display the Process Form.
6. Open the Flex Field Form tab.
7. Search “ps_labor_tracking_option”.
8. Input the desired value:
   • “Insight” value to allow users clock-in/clock-out manually through an alert message (figure 28)
   • “Off” value to disable the alert message
   • “Auto” value to clock-out automatically
9. Save the action.

 

Figure 45: Process Form